在线浏览, 第4页, 永诺 Yongnuo YN560-TX 使用说明书

Ÿ Suppor ts all the YONGNUO YN560 III Flashes Released since January of 2013 Ÿ Two Flash Modes: M/Multi Ÿ Remote control of Flash Output and Zoom per group, up to 6 groups. Ÿ Compatible with RF602/RF603/RF603 II Ÿ 16 Channels Ÿ Large and Clear Screen, User Friendly Interface. Ÿ Transmission Range: 100 Meters. Ÿ Wireless Shutter Receiver of RF603/RF603 II v Please activate the group function of YN560-III with YN560-TX before use, and then remote control the flash mode (flash output) and zoom setup of each group with this controller YN560-TX. It's no need to operate directly on the flash. The flash s c re e n w i l l s y n c h ro n o u s l y d i s p l a y t h e p a r a m e t e r w h i c h i s s e t o n t h e corresponding group of the controller. 1).Install two AA batteries. 2).Install this controller on the hot-shoe of the camera. 3).Turn on the power, and the power indicator light will light. 4).Communication mode (RF602/RF603) setup: Long press [Hz/FN] button, the screen will display the current communication mode of the transceiver t h i s c o n t r o l l e r i s c o m p a t i b l e w i t h . T h e communication mode can be set as RF602 or RF603. Press [OK] button to save and exit. 1).Set communication mode and channel: Set YN560 III as RX slave flash mode, and set its communication mode (RF602/RF603)and channel same as YN560-TX. 2).Activate group function of the flash: Press [ZOOM/CH] button and [Hz/FN] button on the controller simultaneously, the controller will display ACT (ACTIVATE); when the display screen of the flash displays as shown in the picture, press [OK] button on the flash, the group function of YN560 III will be activated. 3).Set flash groups: Press [MODE] button and [TRIG MODE] button on the flash simultaneously to set the flash groups (A-F). 1). Long pressing [ ] button to switch the page of A/B/C group or the page of D/E/F group. M mode: Adjust the flash output of the current group from 1/128 to 1/1 by pressing [RIGHT] button or [LEFT] button; fine tune the flash output (+0.3, +0.7) by pressing [UP] button or [DOWN] button. Multi Mode: Adjustment range of flash output is 1/128-1/4. Enter the zoom setup mode by short pressing [ZOOM/CH] button (setting range is 24-105MM), then save the settings and exit by short pressing [ZOOM/CH] button or [OK] button. 1). Test flash Press [TEST] button on this controller to test flash. 2). Shoot with YN560-TX(Wireless Triggering) When half pressing shutter release button on the camera, this controller will give a wake-up signal, the signal indicator light of this controller turns green and the signal indicator light of the flash turns blue. When full pressing shutter release button on the camera, Yn560 III will flash according to the mode (flash output) set on YN560-TX controller and the signal indicator lights of this controller and the flash turn red; when triggering RF602/RF603/RF603II, the flash output should be adjusted manually on the flash. Ÿ The settings displayed on the flash are subject to the final settings set on the flash or this controller. Product Type: FSK 2.4G wireless controller Distance: 100M Wireless Channel: 16 Flash Mode: M/Multi Group Control: A/B/C/D/E/F Zoom Range: 24-105MM Shutter Interface: 2.5mm shutter interface Battery Type: AA*2 Stand-by Time: 120 hours Dimensions: 70mm*97.5mm*43mm Net Weight: 98g The functions of this manual are based on test conditions of our company. Further notice will not be given if the design and specifications change. The YONGNUO logo in this manual includes the registered trademark or trademark of SHENZHEN YONGNUO PHOTOGRAPHY EQUIPMENT Co., Ltd in China or/and other countries (regions). All other trademarks are the proper ty of their respective owners. Group: A-F Channel:1-16 Flash Count Frequency Flash mode：M/Multi Flash output/zoom Flash output fine tune 1.The flash can't be triggered. 1).Check if the communication mode of this controller is set into the same mode as the flash (transceiver). 2).Check if the channel of this controller is set into the same channel as the flash (transceiver). 2. The flash groups of YN560 III can't be set. Re-activate the flash group of YN560 III with YN560-TX. Ÿ Flash on the transceiver can be triggered synchronously. Ÿ RF603 II should be set in “TRX” state. ①Status indicator light: Green light when waking up (focusing); red light when triggering (shutter). ②Display screen: Displays the current functions status clearly and visually. ③MODE: To set flash modes (M/Multi/- -). ④ : To elect groups (A/B/C/D/E/F). ⑤Interface for shutter release: To implement wireless shutter release function with a shutter release cable connected. ⑥Test button/Power indicator light: When turns on the power, the power indicator light will light on; press this button to test flash. ⑦Zoom/CH: Short press this button to adjust zoom settings (24-105MM); long press this button to set channels (1-16). ⑧Hz/FN: short press this button to adjust multi flash count or multi flash frequency; long press t h i s b u t t o n t o s e t c o m m u n i c a t i o n m o d e s (RF602/RF603). ⑨Power switch: ON/OFF. ⑩Select/Setup button group: To set various parameter, [LEFT] button is to reduce, [RIGHT] button is to increase, [UP] button or [DOWN] button is to fine tune, and [OK] button in the middle is to confirm. More suitable for Canon cameras More suitable for Nikon cameras Press [MODE] button and [ZOOM/CH] button simultaneously till CLA (CLEAR) appeared on the display screen to restore factory settings of this controller. This controller supports using RF603/RF603 II transceiver which set in the same channel to wireless remote control shutter. 1).As shown in the picture, connect this controller to the camera shutter socket with a shutter cable(LS-2.5 series). 2).The camera will focus when you half press the multifunction button on the transceiver in hands, and the focusing indicator light will light (green); the camera will shoot when you full press the multifunction button, and the shutter indicator light will light (red). Ÿ Before this product is connected or installed, please turn off the power of all the associated equipment. Ÿ Keep this product dry. Do not touch it with wet hands, and do not immerse it into water or expose it in the rain. If not, it may work abnormally or damaged. Ÿ Do not use this product in inflammable and explosive places. If not, it may cause fire or explosion. Ÿ This product involves batteries. Refers to the use of batteries, please strictly comply with relevant regulations. If not, it may cause property damage or personally injury. ⑩ ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ In Multi mode, short press [Hz/FN] button to select and set multi flash frequency and multi flash count. 2). Short pressing [ ] button: ①select groups, then press [MODE] button; ② the flash mode will be switched between M, Multi or - - (- - means flash is disabled of the group). Ÿ When this controller is used for non-dedicated cameras, it won't support waking the flash up from the camera, and the triggering function will be unrestricted. 2. Cautions 3.Model Description 5.Preparation 7.Set Group and Flash Mode 8. Set Flash Output of the Current Group 9.Multi Flash Frequency & Flash Count 10. Set Zoom for Each Group 11.Wireless Triggering Function 12.Wireless Shutter Receiver Function 13.Troubleshooting Guide 14.Restore Factory Settings 15.Specification 4.Parts and Explanations 6. Activate Group Function of YN560 III 1.Features ① ② User Manual YN560 III YN560 III RF603 II YN560-TX For C YN560-TX For N 5).Channel setup: Long press [ZOOM/CH] button, when the channel and simulative channel switch on the LCD blink, set this controller and the flash in the same channel. When use this controller with RF602/RF603/RF603II transceiver, the channel switch state of the transceiver should be set into the same as the simulative channel switch . Ÿ After group function of YN560III is activated, the display screen of the flash will synchronously d i s p l a y t h e p a r a m e t e r w h i c h i s s e t o n t h e corresponding group of the controller.