无线设置DocuPrint CM228 fwDPCM225fw_QSG_P1连接到无线网络3自动 SSID 设置注意： 设置无线连接时需要无线 SSID 和密码信息。3选择【无线设定】。.4选择【无线设置向导】。Note: If the required access point does not appear automatically see ‘4 Manual SSID Setup’. 打印机会自动搜索可连接的无线网络。5选择所要连接的网络，然后选择【下一步】。4手动SSID 设定3选择【无线设定】。1按【规格设定】按钮。1按【规格设定】按钮。输入无线网络密码然后选择【确定】。注意： 当自动 SSID 设置成功时。 触摸屏上回短暂显示‘设置完成’。 无线网络信号会显示在触摸屏的右上角。按无线网络标示会显示当前的链接状态。 56WPS-PBC(Operator Panel Menu) Press the small green Energy Saver button to wake up the printer1Clear AllPower SaverOKPress the System button. 2Job StatSystem1Note: WPS-PBC (Operator Panel) and WPS-PIN is onlyavailable when the wireless access point or router supports WPS-PBC. Please refer to the manual provided with the router Before starting WPS-PBC, confirm the position of the WPS button on the wireless access point or router. Please refer to the manual supplied with the router for more information.Press and holdthe WPS button on the printer 1for three (3)seconds.Confirm that the Wi-Fi LED starts to blink slowly and Press WPS Button on WPS Router appears on the LCD panel.2WPS-PBC(Operator Panel Menu)2 Start the WPS operation on the wireless access point or router within two (2) minutes. When WPS is successful, the (Wi-Fi) LED lights up. The wireless connection is established and setup for wireless is complete. At the Operator Panel: WPS-PBC(Operator Panel Menu) 1Note: WPS-PBC (Operator Panel) and WPS-PIN is onlyavailable when the wireless access point or router supports WPS-PBC. Please refer to the manual provided with the router Before starting WPS-PBC, confirm the position of the WPS button on the wireless access point or router. Please refer to the manual supplied with the router for more information.Confirm that the Wi-Fi LED starts to blink slowly and Press WPS Button on WPS Router appears on the LCD panel. Start the WPS operation on the wireless access point or router within two (2) minutes. When WPS is successful, the (Wi-Fi) LED lights up. The wireless connection is establishedand setup for wireless is complete. 3At the Operator Panel: WPS-PIN Confirm that the Wi-Fi LED starts to blink slowly and Press WPS Button on WPS Router appears on the LCD panel. Start the WPS operation on the wireless access point or router within two (2) minutes. When WPS is successful, the (Wi-Fi) LED lights up. The wireless connection is established and setup for wireless is complete. 4选择【无线设置向导】。7 选择网络模式选项然后选择【下一步】如果选择[基础设施]，请执行步骤8. 如果选择请执行步骤9 8 选择网络类型并选择【确定】。可选的秘钥类型如下：*[混合模式 PSK]* [WPA2-PSK-AES]* [WEP]重要：请务必使用一种受支持的加密类型来保护网络通信。使用：混合模式 PSK 或 WPA2-PSK-AESa) 选择加密类型，然后按【确认】。b) 输入密码短语，然后按【确认】。9 选择 WEP 。10 输入WEP密码，然后按【确认】。11选择发送秘钥，然后从WEP秘钥1到WEP秘钥4中选择所需要的秘钥。 然后按【确认】。 可选择的网络模式如下： [基础设施]: 选择并设置有无线网络节点的网络。 [Ad-hoc]: 选择并设置没有节点的无线网络。5选择‘手动SSID 设置’然后选择 【下一步】。注意： 当自动 SSID 设置成功时。 触摸屏上回短暂显示‘设置完成’。 无线网络信号会显示在触摸屏的右上角。按无线网络标示会显示当前的链接状态。 重设无线网络设置53选择【WIFI设定】。使用[向上] 或 [向下] 箭头选择 【重设无线】。4无线网络将被重设。1按【规格设定】按钮。2选择【WIFI设定】。2选择【WIFI设定】。6 输入SSID, 然后选择【下一步】。2选择【无线状态】。5 选择【重设】。7 打印机将重新启动。6 选择【是，重设】。
