在线浏览, 第4页, 博世 Bosch HBC84H500W 安装说明

en The following must be noted: Electrical connection The appliance is fitted with a plug and must only be connected to a properly installed earthed socket. Only a qualified electrician who takes the appropriate regulations into account may install the socket or replace the connecting cable. If the plug is no longer accessible following installation, an all-pole isolating switch must be present on the installation side with a contact gap of at least 3 mm. Contact protection must be ensured by the installation. Fuse protection: see instructions for use - technical data. Fitted units This appliance is only intended to be fully fitted in a kitchen. This appliance is not designed to be used as a tabletop appliance or inside a cupboard. The fitted cabinet must not have a back wall behind the appliance. A gap of at least 45 mm must be maintained between the wall and the base or back panel of the unit above. The fitted cabinet must have a ventilation opening of 50 cm 2 on the front. To achieve this, cut back the base panel or fit a ventilation grille. Ventilation slots and intakes must not be covered. The safe operation of this appliance can only be guaranteed if it has been installed in accordance with these installation instructions. The fitter is liable for any damage resulting from incorrect installation. The units into which the appliance is fitted must be heat-resistant up to 90 ºC, and adjacent unit fronts up to at least 65 ºC. Appliance in the upper cabinet - Fig. 1 Oven under the work surface - Fig. 2 There must be a ventilation cut-out made in the intermediate floor of the base unit - see Fig. 2. If the appliance is being installed beneath a hob, observe the hob assembly instructions. Corner installation - Fig. 3 The dimensions must be taken into consideration for corner installation. Securing the appliance in place - Fig. 4 J Fully insert the appliance and centre it. J Do not kink the connecting cable. J Screw the appliance into place. J The gap between the worktop and the appliance must not be closed by additional battens. Removal Disconnect the appliance from the power supply. Undo the securing screws. Raise the appliance slightly and pull it out completely. zh 必须注意下列事项： 电气连接 本电器装有插头，只能连接到带有正确 接地措施的插座上。只能由电气专业人 员按照有关规定来安装插座或更换电 源线。 安装后，如果插头使用不便，则必须在 安装侧安装一个全电极隔离开关，触点 间隙至少为 3 mm。 安装方式必须确保良好的触点保护。 保险丝保护：参阅使用说明—技术 参数。 安装橱柜 本电器仅供在整体式厨房内安装使用。 本电器不可作为桌上设备或置于壁橱内 使用。 安装橱柜不得有背板 (在电器后方)。墙 壁和上方橱柜的底板或背板之间必须保 持至少 45 mm 的间距。 装设橱柜的正面必须留下 50 cm 2 的通风 口。为此，切割底板或安装通风格栅。 不得遮盖通风槽和进气口。只有按照下 列操作说明进行安装才能保证电器安全 工作。对于由于不当安装引起的损坏， 应由安装人员承担责任。安装本电器的 橱柜必须能够承受最高达 90 _C 的高 温，相邻的橱柜表面必须能够承受最高 达 65 _C 的高温。 电器安装于上方橱柜 - 图 1 电器安装于工作台面下方 - 图 2 电器的安装橱柜中间底板上必须开有通 风槽 - 参见图 2 如果将电器安装在灶具下方，要遵守灶 具安装说明。 电器安装于转角位置 - 图 3 安装在转角位置时必须考虑尺寸是否 合适。 将电器紧固到位 - 图 4 J 完全插入电器并使其居中放置。 J 不要扭结连接电缆。 J 将电器螺丝拧到位。 J 切勿使用附加木条将工作台面和电器 之间的间隙封闭起来。 拆卸 断开电器电源。拧开固定螺钉。稍微抬 高电器并将其完全拉出。