4|KCA-BT200Before Use• You need to register your cell-phone before using it with this unit. For more details, see Bluetooth device> (page 12).• If you have registered two or more cell-phones, you need to select one of them. For more details, see Connect> (page 14).• To use the Phone Book, it must be downloaded to this unit in advance. For details, see the Phone Book> (page 13).• For the method of operation in the Menu mode, refer to the Instruction Manual for Control Unit.• For more information regarding the function with [] mark, see (page 23).Making a callDialing Method1. Select dialing method item during Menu modeSelect the "DIALING MODE"/ "D.MODE" display.2. Select a dialing methodPress the [38] button.• "NUMBER DIAL" » "PHONE BOOK1" » "PHONE BOOK2" » "OUT-CALL" » "IN-CALL" » "MISSED CALLS"• "N-DIAL" » "PH-BOOK1" » "PH-BOOK2" » "OUT-CALL" » "IN-CALL" » "MIS-CALL"3 Methods of operations in the above modes are described below.3. Exit the dialing method selection modeExit Menu mode.3 Dial a number ()2-1. Select the "NUMBER DIAL"/ "N-DIAL" display.2-2. Enter a phone numberPress the number ([1] – [0]), #([FM]), *([AM]), or +([¢]) button on the remote controller.2-3. Make a callPress the [DIRECT] button on the remote controller.☞ You can input max 32 digits.3 Speed dialing (Preset dial)2-1. Select the "NUMBER DIAL"/ "N-DIAL" display.2-2. Select the preset dial numberPress the [1] – [6] button.2-3. Make a callPress the [38] button for at least 1 second.☞ You need to register the preset dial number. (page 5)3 Calling a number in the call log ()2-1. Select the "OUT-CALL" (outgoing call), "IN-CALL" (incoming call), or "MISSED CALLS"/"MIS-CALL" (missed call) display.Basic Operation of hands-free phoning (Model-A)2-2. Select a name or phone numberPush the Control knob towards up or down.2-3. Make a callPress the [38] button for at least 1 second.3 Calling a number in the Phone Book ()2-1. Select the "PHONE BOOK1"/"PH-BOOK1" display, proceed to step 2-2.Select the "PHONE BOOK2"/"PH-BOOK2" display, proceed to step 2-3.2-2. Select the initial to be searched forOperation typeOperationMove to the next character. Push the Control knob towards right or left.Move to the next row. Push the Control knob towards up or down.Determine the selected initialPress the [38] button for at least 1 second.2-3. Select the nameOperation typeOperationChange the name.Push the Control knob towards up or down.Change the initial.Push the Control knob towards right or left.2-4. Make a callPress the [38] button for at least 1 second.Make a voice dialing call 1. Select voice recognize item during Menu modeSelect the "VOICE RECOG"/ "V-RECOG" display.2. Press the [38] button for at least 1 second."V-RECOG READY"/ "VR READY" is displayed.3. Press the [38] button."PB NAME" is displayed.When a beep is heard, utter the name within 2 seconds.4. "PB TYPE"/ "PN type" is displayed.When a beep is heard, utter the category within 2 seconds.5. Make a callThis step is the same as step 3 of the procedure in . You can make a call or select a category.☞ If your voice cannot be recognized, a message is displayed. Pressing the [38] button allows you to retry voice input. (page 26)☞ Both the name and category requires registration of a voice tag. (page 15)☞ Audio sound is not output during voice recognize.Display of phone number type (category)DisplayDescriptionDisplayDescription"GE"/ "GENERAL" General"OF"/ "OFFICE"Office"HM"/ "HOME"Home"OT"/ "OTHER"Other"MO"/ "MOBILE" MobileB64-4124-00_00_M_EngChs.indb 4B64-4124-00_00_M_EngChs.indb 408.2.15 4:05:02 PM08.2.15 4:05:02 PM
